Replacement Caution: If the four bezel clips are shaped as shown below, make sure any loose clips are inserted correctly in the slot-load bezel.
2007 APPLE MACBOOK PRO INSTALL
Install the right side of the top case first (near the disc bezel) to lock the bezel clips and prevent any of the clips from becoming loose inside the computer. Make sure they are in place while reassembling the computer and before installing the top case. Replacement Caution: If any of the four bezel clips at the slot-load bezel come loose, simply insert them back in the slots. Replacement Note: Before replacing the top case, make sure to connect the trackpad flex cable to the logic board. Replacement Note: The top case includes heatstaked keyboard, webbing, EMI shield, a small rectangular foam pad, and attached trackpad cable. Refer to the following notes to install the replacement top case, and reassemble and test the computer. Lift the top case up and away from the computer assembly.ġ5. Use the flat end of a black stick to reach in and disconnect the trackpad cable. Raise up the top case so you can see where the folded trackpad flex cable attaches to the logic board. With the top and right side gap opened, tilt up-but do not remove-the right edge of the top case.This motion releases the remaining snaps between the top case and bottom case, and the slot-load bezel clips become loose as the top case is tilted up.ġ2. Starting at the left corner and working in a counter-clockwise direction, use an access card tool to open the gap along the front of the top case, around the perimeter, and to the right side above the optical drive slot.ġ1. Be especially careful with the left front corner of the top case. Warning: Inserting a tool too far or performing this step too quickly could break some of the snaps that secure the top case.Open the display to a 90-degree angle or wider.To prevent a wobble symptom, use light pressure to hold the top case onto the assembly when installing the screws. Replacement Caution: When installing these three screws, an incorrect installation could cause the reassembled computer to wobble in use. Keep the screwdriver in line with the screw head as much as possible. One longer 4.5-mm long screw at the corner of the battery bay nearest the battery connectorīecause this is a recessed area, the screwdriver has to go in at an angle.In the battery bay, use a long-handled screwdriver to remove the three #00 Phillips screws at the inner edge of the battery bay near where the RAM slots are located: Do not remove the two screws that are closest to the battery connector.Ĩ. In the battery bay, remove the two 6-mm long identical screws that are on both outer sides of the battery connector. Tip: To help remember the screw sequence, think of it as "2, 4, 7, 9 loosens the top case every time."ħ. Starting at the corner closest to the battery connector, skip the first screw, then remove the second, fourth, seventh, and ninth screw. Remove the 3-mm long identical screws as follows: Important: Remove only the four screws shown.Notice the long row of #0 Phillips screws at the front edge of the battery bay.Replacement Caution: When installing the three bottom case screws, install them in the order shown. Two 14-mm long screws near display hinge One 11-mm long at center of bottom case Replacement Caution: Do not put one of the longer screws in the center screw hole or it will damage the logic board. Turn over the computer, and on the outside of the bottom case, remove the three #0 Phillips screws: Two 8-mm long shoulder screws at the back corners of the computerĤ.Two 12-mm long shoulder screws that are closest to the hinge.At the back of the computer, remove the four #0 Phillips screws (two at each side) near the display hinge.
If they are removed, however, be sure to reinstall the two identical 3-mm long shoulder screws at the corner near the ports. Although they can be removed, they exist for cosmetic purposes only and do not require removal. Important: Notice the two screws at the left side of the computer.
The slot-drive bezel could be damaged with too much pressure.Ģ.
Replacement Caution: When installing these top case screws, do not press on the area over the slot drive. With the computer upright, remove the two identical 5.5-mm long shoulder screws from the right side of the computer. Caution: To prevent scratches or other cosmetic damage to the computer housing, use a soft cloth as a protective layer when removing and installing the external screws.ġ.
0 kommentar(er)
